Showing 1–80 of 172 results

  • BC05 – Swivel Elbow

    POA
    Type BC05 fitting has been designed as a variable angle in-line connection, adjustable through 202°.
    # Tube Size A B kg
    G2533.7 60 33 0.51
    G3242.4 73 36 0.81
    G4048.3 83 45 1.14
    View Size Chart...
    Clear selection
  • C00 Sleeve Joint

    POA
    The Sleeve Joint is designed to provide an in-line joint between two tubes of the same diameter.
    # Tube Size A kg
    G2026.9 76 0.33
    G2533.7 89 0.39
    G3242.4 102 0.50
    G4048.3 100 0.55
    G5060.3 120 1.14
    View Size Chart...
    Clear selection
  • C01 Expanding Connector

    POA
    The expanding Connector is designed to provide an in line joint between tubes of the same diameter, and a wall thickness of 3.2mm. It fits flush with the tube surface and can be located inside other fittings. It must not be used as a load-bearing joint, for such applications use a FastClamp type C00.
    # Tube Size A B kg
    G2533.7 75 19 0.18
    G3242.4 75 19 0.27
    G4048.3 75 19 0.35
    View Size Chart...
    Clear selection
  • C02 90° Elbow

    POA
    The 90° Elbow is designed to provide a joint between two tubes at right angles to each other. Often used for railing ends and corners.
    # Tube Size A kg
    G2026.9 40 0.24
    G2533.7 48 0.39
    G3242.4 60 0.53
    G4048.3 67 0.68
    G5060.3 86 1.53
    View Size Chart...
    Clear selection
  • C03 Short Tee

    POA
    The Short Tee is designed to provide a butt joint between two tubes at right angles to each other. Often used for railing ends and tops. If tubes need to be joined inside the fitting then a C04G type should be used.
    # Tube Size A B kg
    G2026.9 40 38 0.21
    G3242.4 60 54 0.44
    G4048.3 67 60 0.56
    G5060.3 86 71 0.76
    View Size Chart...
    Clear selection
  • C04 Long Tee

    POA
    The Long Tee is designed to provide a butt joint between two tubes at right angles to each other. Often used for railing ends and tops. It allows the through tube to be joined inside the fitting. An alternative is the C03G type fitting.
    # Tube Size A B kg
    G2026.9 40 80 0.35
    G2533.7 48 96 0.52
    G3242.4 60 120 0.77
    G4048.3 67 134 0.88
    G5060.3 86 172 1.33
    View Size Chart...
    Clear selection
  • C041 Level to Sloping Down Tee (30° to 45°)

    POA
    Used to form a Tee on handrails where the rail changes from level to sloping down the stairs. Adjustable between 30° & 45°.
    # Tube Size A B kg
    G3242.4 140 60 1.02
    G4048.3 156 68 1.12
    View Size Chart...
    Clear selection
  • C042 Level to Sloping Up Tee (30° to 45°)

    POA
    Used to form a Tee on handrails where the rail changes from level to sloping up the stairs. Adjustable between 30° & 45°
    # Tube Size A B kg
    G3242.4 140 60 1.02
    G4048.3 155 68 1.12
    View Size Chart...
    Clear selection
  • C05 Variable Elbow (15° to 60°)

    POA
    The Variable Elbow is designed to make joints at an angle of between 15° and 60°.
    # Tube Size A B C D kg
    G2533.7 67 50 13 40 0.43
    G3242.4 80 66 15 56 0.66
    G4048.3 95 75 21 52 0.91
    View Size Chart...
    Clear selection
  • C05A Variable Elbow (11° to 30°)

    POA
    The variable elbow is designed to make joints at an angle of between 11° & 30°.
    # Tube Size A B C D kg
    G3242.4 72 61 13 75 0.82
    G4048.3 85 73 19 84 1.01
    View Size Chart...
    Clear selection
  • C06 Internal T Joint

    POA
    The Internal T joint is designed to provide an angled joint between a tube and a FastClamp fitting when used in conjunction with C02G and C03G type fittings. Often used for railing tops and midrails to accommodate a slope as offset railing
    # Tube Size A B C kg
    G2533.7 23 33 34 0.33
    G3242.4 29 42 40 0.54
    G4048.3 31 48 44 0.68
    View Size Chart...
    Clear selection
  • C07 45° Tee

    POA
    The 45° Tee is used as a bracing and strut component for strengthening structures.
    # Tube Size A kg
    G2533.7 45 0.38
    G3242.4 54 0.63
    G4048.3 60 0.83
    View Size Chart...
    Clear selection
  • C10G Swivel Base

    POA
    The Swivel Base is designed to provide a base fixing. It is usually used in conjunction with a C36G type fitting to make a C46G type base swivel combination. This fitting does not provide sufficient rigidity to be used as a railing base without other means of support.
    # Tube Size A B C D E kg
    #N/A 55 40 50 85 115 0.51
    View Size Chart...
    Clear selection
  • C11 Wall Flange

    POA
    The Wall Flange is designed to provide a positional wall or base fixing. It is not recommended to use this fitting as a structural railing base.
    # Tube Size A B C D Ø kg
    G2026.9 86 42 57 4 9 0.35
    G2533.7 89 45 64 6 9 0.39
    G3242.4 102 50 76 6 9 0.50
    G4048.3 114 57 89 6 9 0.65
    G5060.3 127 64 95 6 9 1.10
    View Size Chart...
    Clear selection
  • C12 Railing Base Flange

    POA
    The Railing Base is designed to provide a base for railings and other structures. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions, see table 3 on our FastClamp Technical Data page.
    # Tube Size A B C D E Ø kg
    G2026.9 76 65 8 76 114 11 0.60
    G2533.7 89 76 9 89 128 14 0.91
    G3242.4 89 80 10 102 140 14 1.03
    G4048.3 89 89 10 114 152 14 1.24
    G5060.3 128 88 9 127 165 18 1.89
    View Size Chart...
    Clear selection
  • C13 Railing Verticle Side Support

    POA
    The Railing Vertical Side Support is designed to provide a base for railings and other structures that need a side mounted fixing. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions, see table 3 on our FastClamp Technical Data page.
    # Tube Size A B C D E Ø kg
    G2533.7 45 96 67 28 104 14 0.95
    G3242.4 50 109 78 30 114 14 1.20
    G4048.3 60 123 86 34 120 14 1.50
    View Size Chart...
    Clear selection
  • C14 Railing Horizontal Side Support

    POA
    The Railing Horizontal Side Support is designed to provide a base for railings and other structures that need a side mounted fixing. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions, see table 3 on our FastClamp Technical Data page.
    # Tube Size A B C D Ø kg
    G2533.7 90 30 12 150 18 1.08
    G3242.4 90 35 12 150 18 1.32
    G4048.3 90 41 15 150 18 1.67
    View Size Chart...
    Clear selection
  • C15 Side Palm Fixing

    POA
    The Side Support is designed to provide a base for railings and other structures that need a side mounted fixing. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions, see table 3 on our Technical Data Page.
    # Tube Size A B C D E Ø kg
    G2533.7 76 89 71 63 97 11 0.63
    G3242.4 84 98 82 72 108 11 0.80
    G4048.3 92 104 86 78 112 11 0.84
    View Size Chart...
    Clear selection
  • C16 Handrail Bracket

    POA
    The Handrail Bracket is designed to secure handrail tube to a wall. It can also be used on top of walls as a fixing for a low rail.
    # Tube Size A B C D Ø kg
    G2026.9 46 57 54 76 8 0.36
    G2533.7 44 63 57 82 11 0.46
    G3242.4 44 76 63 102 11 0.57
    G4048.3 48 85 67 108 11 0.62
    View Size Chart...
    Clear selection
  • C17 Ground Support

    POA
    The Ground Socket is designed to provide a base that can be cast into the ground to support a post. The post is removable. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions, see table 3 on our Technical Data Page.
    # Tube Size A B C D kg
    G2533.7 61 140 130 4.5 1.42
    G3242.4 61 140 130 4.5 1.42
    G4048.3 61 140 130 4.5 1.42
    View Size Chart...
    Clear selection
  • C18 Base Flange with Integrated Toeboard

    POA
    The Base Flange with Integrated Toeboard is ideal for guardrailing and balustrading applications where the addition of a toeboard is required. The side plates have slotted holes to allow for a degree of sideways movement for ease of installation. It is recommended that this fitting be used in accordance with FastClamp maximum post centre dimensions, see table 3 on our Technical Data Page.
    # Tube Size A B C D E Ø kg
    G3242.4 45 90 58 30 100 18 2.14
    G4048.3 45 90 58 30 100 18 2.28
    View Size Chart...
    Clear selection
  • C20 3 Way 90° Elbow

    POA
    The 3 way 90° Elbow is designed to provide a neat corner for the upper rail of guardrail or frames.
    # Tube Size A kg
    G2026.9 40 0.37
    G2533.7 48 0.51
    G3242.4 60 0.80
    G4048.3 67 0.97
    G5060.3 84 1.82
    View Size Chart...
    Clear selection
  • C200 Double Sided Fixing Bracket

    POA
    The Type C200 is used as an attachment point for flat sheets or boards and comes supplied with a drilled hole.
    # Tube Size A B C D E F Ø kg
    G2533.7 45 45 5 90 70 25 6.5 0.18
    G3242.4 53 55 6 106 86 40 11.5 0.38
    G4048.3 56 61 6 112 92 40 11.5 0.59
    View Size Chart...
    Clear selection
  • C201LH Left hand Level to Sloping Down Side Outlet Elbow (30° to 45°)

    POA
    Used to form a Left Hand Side Outlet Elbow on handrails where the top rail changes from level to sloping down the stairs. Adjustable between 30° & 45°
    # Tube Size A B C kg
    G3242.4 86 60 42 1.08
    G4048.3 93 68 47 1.28
    View Size Chart...
    Clear selection
  • C201RH Right hand Level to Sloping Down Side Outlet Elbow (30° to 45°)

    POA
    Used to form a Right Hand Side Outlet Elbow on handrails where the top rail changes from level to sloping down the stairs. Adjustable between 30° & 45°
    # Tube Size A B C kg
    G3242.4 86 60 42 1.08
    G4048.3 93 68 47 1.28
    View Size Chart...
    Clear selection
  • C21 Corner c/w Through Tube

    POA
    The Corner Complete with through tube is designed to provide a 90° corner for the intermediate rail of guardrail or frames.
    # Tube Size A B kg
    G2026.9 40 38 0.21
    G2533.7 48 45 0.39
    G3242.4 60 54 0.58
    G4048.3 67 60 0.69
    G5060.3 86 71 1.10
    View Size Chart...
    Clear selection
  • C211LH Left hand Level to Sloping Down Side Outlet Tee (30° to 45°)

    POA
    Used to form a Left Hand Side Outlet Tee on hand-rails where the mid rail changes from level to sloping down the stairs. Adjustable between 30° & 45°
    # Tube Size A B C kg
    G3242.4 86 60 44 0.96
    G4048.3 93 68 48 1.12
    View Size Chart...
    Clear selection
  • C211RH Right hand Level to Sloping Down Side Outlet Tee (30° to 45°)

    POA
    Used to form a Right hand Side Outlet Tee on hand-rails where the mid rail changes from level to slop-ing down the stairs. Adjustable between 30° & 45°
    # Tube Size A B C kg
    G3242.4 86 60 44 0.96
    G4048.3 93 68 48 1.12
    View Size Chart...
    Clear selection
  • C22 Two Socket Cross

    POA
    The Two Socket Cross fitting provides the midrail joint for handrail and other structures. It is recommended that the handrail post is continuous through the fitting.
    # Tube Size A B kg
    G2026.9 40 80 0.28
    G2533.7 48 95 0.39
    G3242.4 60 120 0.57
    G4048.3 67 134 0.65
    G5060.3 86 172 1.26
    View Size Chart...
    Clear selection
  • C221 Level to Sloping Down / Up Cross (30° to 45°)

    POA
    Used to form a cross on handrails where the mid rail changes from either level to sloping down or level to sloping up the stairs. Adjustable between 30° & 45°.
    # Tube Size A B kg
    G3242.4 138 60 0.82
    G4048.3 155 68
    View Size Chart...
    Clear selection
  • C229 Single Socket Tee (11° to 30°)

    POA
    The adjustable Short Tee fitting will accommodate any rake angle from 11° to 30°. It can be used for any Tee Joint to make an angle of between 11° & 30°.
    # Tube Size A B kg
    G3242.4 99 54 0.73
    G4048.3 109 59 0.86
    View Size Chart...
    Clear selection
  • C23 45° Side Outlet Tee

    POA
    The Side Outlet Tee fitting provides a three way midrail joint for handrail and other structures. It is recommended that the handrail post is continuous through the fitting.
    # Tube Size A B kg
    G2026.9 40 38 0.32
    G2533.7 48 45 0.55
    G3242.4 60 54 0.83
    G4048.3 66 60 0.84
    G5060.3 86 71 1.48
    View Size Chart...
    Clear selection
  • C24 4 Way Cross + Central Tube

    POA
    The 4 Way Cross fitting provides a four way midrail joint for handrail and other structures. It is recommended that the handrail post is continuous through the fitting. This fitting may also be used for the top rail with the centre post capped with a C65 Plastic Stop End.
    # Tube Size A B kg
    G2026.9 41 54 0.43
    G2533.7 48 67 0.75
    G3242.4 60 78 1.14
    G4048.3 67 70 1.19
    G5060.3 86 106 2.12
    View Size Chart...
    Clear selection
  • C245 Three Socket Tee (30° to 45°)

    POA
    This fitting is used on Safety Railing with slopes be-tween 30° & 45° and fixes the top rail to a vertical intermediate upright
    # Tube Size A kg
    G3242.4 180 0.95
    G4048.3 216 1.22
    View Size Chart...
    Clear selection
  • C25 Short Tee Swivel (Normally used in pairs)

    POA
    Short Tee Swivel fittings are normally used in pairs to facilitate corner angles of 90° to 180°. It is also used on staircases with a C02 and C03 fittings in conjunction with a short piece of tube and a C65 Plastic End Cap in landing areas. When ordering please specify the number of fittings required, not the number of pairs.
    # Tube Size A kg
    G2026.9 65 0.31
    G2533.7 66 0.37
    G3242.4 73 0.48
    G4048.3 81 0.49
    G5060.3 110 0.85
    View Size Chart...
    Clear selection
  • C28 Adjustable 2 Socket Cross (30° to 45°)

    POA
    The Adjustable 2 Socket Cross fitting will accommodate any rake angle from 30° to 45°. This fitting is not recommended as the top fitting on a guardrail or balustrade system, use the C29 Adjustable Short Tee.
    # Tube Size A kg
    G2533.7 162 0.71
    G3242.4 190 1.12
    G4048.3 218 1.38
    View Size Chart...
    Clear selection
  • C29 Adjustable Short Tee (30° to 60°)

    POA
    The Adjustable Short Tee fitting will accommodate any rake angle from 30° to 60°. This fitting is commonly used for the top rail of handrail to accommodate the rake angle on slopes. It can also be used for any Tee Joint to make at an angle of between 30° and 60° for light weight structures.
    # Tube Size A B kg
    G2533.7 74 52 0.47
    G3242.4 85 63 0.63
    G4048.3 102 72 0.78
    View Size Chart...
    Clear selection
  • C30 Collar

    POA
    The Collar fitting can be used to support the C03 fitting when the latter is used as a hinge. It can also be used to increase the load capacity of another fitting when used together. The C30 can be used as a stop for a sliding tube.
    # Tube Size A kg
    G2026.9 25 0.08
    G2533.7 25 0.13
    G3242.4 25 0.16
    G4048.3 25 0.18
    G5060.3 40 0.32
    View Size Chart...
    Clear selection
  • C31 Gate Eye

    POA
    This fitting is designed as a gate eye for light weight gates. If a heavy gate is being used we recommend that C03 and C30 type fittings are used to support the gate.
    # Tube Size A B C kg
    G2026.9 25 30 15 0.14
    G2533.7 25 33 15 0.19
    G3242.4 25 38 15 0.25
    G4048.3 25 41 15 0.26
    View Size Chart...
    Clear selection
  • C32 Gate Hinge

    POA
    This fitting is designed as a gate hinge for light weight gates. If a heavy gate is being used we recommend that C03 and C30 type fittings are used to support the gate.
    # Tube Size A B C D kg
    G2026.9 30 25 13 38 0.21
    G2533.7 30 25 10 25 0.27
    G3242.4 34 27 10 27 0.30
    G4048.3 37 27 10 27 0.32
    View Size Chart...
    Clear selection
  • C33 Hook

    POA
    The fitting is designed to provide an attachment for chain.
    # Tube Size A B C D kg
    G2026.9 28 25 10 19 0.17
    G2533.7 35 25 13 21 0.24
    G3242.4 39 25 13 25 0.25
    G4048.3 41 25 13 25 0.30
    View Size Chart...
    Clear selection
  • C34 Fixing Pad

    POA
    The fitting is designed to provide an attachment for flat sheets or board. It may also be used as a gate stop. An alternative fitting for the attachment of boards is the C35 type.
    # Tube Size A B C Ø kg
    G2533.7 45 25 5 9 0.16
    G3242.4 53 40 5 12 0.32
    G4048.3 56 40 5 12 0.35
    View Size Chart...
    Clear selection
  • C35 Male Swivel

    POA
    The Male Swivel can be used on its own for use with a shakle and chain or with the C36 female swivel to mount rails at any angle for slopes. It can also be used for attaching flat sheets or boards to a structure and is available assembled with the C36 fittings as a C45 single swivel combination.
    # Tube Size A B C Ø kg
    G2026.9 32 38 8 11 0.15
    G2533.7 32 42 8 11 0.20
    G3242.4 32 47 8 11 0.21
    G4048.3 32 50 8 11 0.24
    G5060.3 48 60 8 11 0.47
    View Size Chart...
    Clear selection
  • C36F Female Swivel

    POA
    The Female Swivel is designed as part of the swivel combination group of fittings. It can be used with the C10, C35, C37, C38 or C36M male swivel fittings.
    # Tube Size A B C D Ø kg
    G2026.9 39 35 58 10 11 0.24
    G2533.7 41 35 60 10 11 0.33
    G3242.4 44 35 63 10 11 0.38
    G4048.3 50 35 70 10 11 0.46
    G5060.3 70 40 95 10 11 0.84
    View Size Chart...
    Clear selection
  • C36M Male Swivel

    POA
    The Male Swivel is designed as part of the swivel combination group of fittings. It can be used with C36F fittings.
    # Tube Size A B kg
    G2533.7 35 60 0.28
    G3242.4 45 70 0.40
    G4048.3 50 75 0.44
    View Size Chart...
    Clear selection
  • C37 Double Male Swivel

    POA
    The Double Male Swivel is designed as part of the swivel combination group of fittings. It can be used with two C36 female swivel fittings. The double swivel combination is also available assembled as a type C47 fitting
    # Tube Size A B C Ø kg
    G2026.9 40 32 8 11 0.21
    G2533.7 44 32 8 11 0.28
    G3242.4 49 32 8 11 0.32
    G4048.3 52 32 8 11 0.46
    G5060.3 63 50 8 11 0.51
    View Size Chart...
    Clear selection
  • C38 90° Corner Male Swivel

    POA
    The 90° Corner Male Swivel is designed as part of the swivel combination group of fittings. It can be used with two C36 female swivel fittings to make a corner combination fitting which is also available assembled as a type C48 type fitting
    # Tube Size A B C Ø kg
    G2026.9 40 39 8 11 0.22
    G2533.7 44 38 8 11 0.34
    G3242.4 49 48 8 11 0.39
    G4048.3 53 48 8 11 0.47
    View Size Chart...
    Clear selection
  • C40 90° Crossover

    POA
    The 90° Crossover connects two rails at 90° to each other and is often used for the handrailing when continuous standard lengths of tube are used. Please note that tube joints should use the C00 or C01 type fitting, and not the C40 type fitting.
    # Tube Size A B kg
    G2026.9 36 35 0.22
    G2533.7 40 40 0.34
    G3242.4 49 49 0.41
    G4048.3 55 55 0.57
    G5060.3 61 64 0.82
    G25-3233.7/42.4 45 45 0.46
    G25-4033.7/48.3 53 50 0.57
    G32-4042.2/48.3 51 52 0.59
    View Size Chart...
    Clear selection
  • C41 Clamp on Tee

    POA
    The Clamp on Tee is designed to allow a new tube to be joined to an existing structure. Torque maximum 15NM. This uses a M10 stainless steel bolt.
    # Tube Size A B kg
    G2026.9 50 37 0.28
    G2533.7 53 37 0.45
    G3242.4 67 48 0.61
    G4048.3 77 55 0.79
    G5060.3 90 62 0.97
    View Size Chart...
    Clear selection
  • C42 Clamp on Crossover

    POA
    The Clamp on Crossover is designed to allow a new tube to be joined to an existing structure.
    # Tube Size A B C D kg
    G2026.9 40 28 28 28 0.15
    G2533.7 48 34 34 34 0.27
    G3242.4 58 43 43 43 0.47
    G4048.3 65 49 49 49 0.54
    G5060.3 78 62 61 61 0.74
    View Size Chart...
    Clear selection
  • C43 Combination Socket

    POA
    The Combination Socket is designed for racking and similar systems to allow a crossover to be combined with a cross tie.
    # Tube Size A B C kg
    G2026.9 30 35 40 0.28
    G2533.7 40 40 48 0.49
    G3242.4 45 50 60 0.75
    G4048.3 51 56 67 0.90
    G5060.3 61 68 86 1.72
    View Size Chart...
    Clear selection
  • C45 Single Swivel Combination

    POA
    The Single Swivel Combination is designed to provide and angled tee between two tubes. It can be used to construct sloping handrail and for providing bracing struts to structures.
    # Tube Size A kg
    G2026.9 N/A 0.42
    G2533.7 N/A 0.55
    G3242.4 N/A 0.62
    G4048.3 N/A 0.73
    G5060.3 N/A 1.34
    View Size Chart...
    Clear selection
  • C46 Base Swivel Combination

    POA
    The Base Swivel Combination is designed to provide an angled wall or floor mounting. This fitting should not be used as a railing base without suitable support.
    0.620.870.810.850.96
    # Tube Size kg
    View Size Chart...
    Clear selection
  • C47 Double Swivel Combination

    POA
    The Double Swivel Combination is designed to provide an in line angled joint as a post, this is suitable for the mid rail of a sloping handrail or to provide bracing to a structure.
    0.780.990.811.322.50
    # Tube Size kg
    View Size Chart...
    Clear selection
  • C48 90° Corner Swivel Combination

    POA
    The 90° Corner Swivel Combination is designed to provide an angled joint at a post, this is suitable for the mid rail of sloping handrail or to provide bracing to a structure.
    0.751.001.121.46
    # Tube Size kg
    View Size Chart...
    Clear selection
  • C50 Slope Elbow (0° to 11°)

    POA
    The Slope Elbow is designed to provide an elbow for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.
    # Tube Size A kg
    G3242.4 60 0.81
    G4048.3 70 1.02
    View Size Chart...
    Clear selection
  • C51 Short Slope Tee (0° to 11°)

    POA
    The Slope Short Tee is designed to provide a T joint between two tubes for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.
    # Tube Size A B kg
    G3242.4 68 60 0.57
    G4048.3 75 68 0.76
    View Size Chart...
    Clear selection
  • C52 Long Slope Tee (0° to 11°)

    POA
    The Slope Long Tee is designed to provide a T joint between two tubes for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.
    # Tube Size A B kg
    G3242.4 144 60 1.06
    G4048.3 158 67 1.10
    View Size Chart...
    Clear selection
  • C53 Slope Base (0° to 11°)

    POA
    The Slope Base is designed to provide a base for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.
    # Tube Size A B C D E Ø kg
    G3242.4 91 140 89 102 10 14 0.90
    G4048.3 96 152 89 114 10 14 1.40
    View Size Chart...
    Clear selection
  • C54 Slope 2 Socket Cross (0° to 11°)

    POA
    The Slope 2 Socket Cross is designed to provide a joint for the midrail for use on ramps. The variable angle allows the fitting to accommodate slopes up to 11°.
    # Tube Size A B kg
    G3242.4 144 72 0.97
    G4048.3 158 79 1.00
    View Size Chart...
    Clear selection
  • C55 27½° Ridge Fitting

    POA
    A four way socket fitting used to construct the ridge of a roof structure.
    # Tube Size A B kg
    G4048.3 67 89 1.00
    View Size Chart...
    Clear selection
  • C56 27½° Eaves Fitting

    POA
    A four way socket fitting used to construct the eaves of a roof structure.
    # Tube Size A B C D kg
    G4048.3 67 89 83 46 1.16
    View Size Chart...
    Clear selection
  • C57 Three Socket Tee (11° to 30°)

    POA
    Similar to a type C27, it is used on Safety Railing with slopes between 11º30º and fixes the top rail to a vertical intermediate upright. Unlike the type C27 these components are ex-stock and do not require machining
    # Tube Size A B kg
    G3242.4 180 62 1.16
    G4048.3 216 70 1.46
    View Size Chart...
    Clear selection
  • C58 Two Socket Cross (11° to 30°)

    POA
    Similar to a type C26, it is used on Safety Railing with slopes between 11º30º and fixes the mid rail to a vertical intermediate upright. Unlike the type C26 these components are ex stock and do not require machining
    # Tube Size A B kg
    G3242.4 180 62 0.97
    G4048.3 216 70 1.26
    View Size Chart...
    Clear selection
  • C59 Angle Base Flange (11° to 30°)

    POA
    Similar to a type C53, it is used to set the upright at an angle between 11º– 30º. This fitting should only be subjected to light loads which cannot be positioned at 90º to the applied load. For greater loads or other tube sizes a type C12 flange should be used with the upright bent to the required angle Ø indicates the diameter of the fixing hole.
    # Tube Size A B C D Ø kg
    G3242.4 76 114 79 146 14 1.27
    G4048.3 89 124 90 164 14 1.42
    View Size Chart...
    Clear selection
  • C59A Angle Base Flange (30° to 45°)

    POA
    Similar to a type C59, it is used to set the upright at an angle between 30° & 45°. This fitting should only be subjected to light loads which cannot be positioned at 90° to the applied load. For greater load use a type C12
    # Tube Size A B C D kg
    G3242.4 76 106 81 138 1.17
    G4048.3 89 115 85 155 1.53
    View Size Chart...
    Clear selection
  • C60 Spare Screws

    POA
    Spare Screws come in two sizes, 1/4” ISO 228 for the 20 and 25nb range and 3/8” ISO 228 for the 32, 40 and 50 ranges.
    # Tube Size A B C D E
    S2526.9 N/A
    S2533.7 N/A
    S2542.4 N/A
    S32/4048.3 N/A
    S32/4060.3 N/A
    View Size Chart...
    Clear selection
  • C61 Allen Keys

    POA
    Allen keys are available in two sizes, the first is suitable for the 20 and 25nb fitting and the other for the 32, 40 and 50nb fittings.
    # Tube Size A B C D E
    S2526.9 N/A
    S2533.7 N/A
    S2542.4 N/A
    S32/4048.3 N/A
    S32/4060.3 N/A
    View Size Chart...
    Clear selection
  • C62R Ratchet Keys

    POA
    The Ratchet driver and dual keys are available to speed assembly. The Ratchet driver will allow tightening to the correct torque.
    # Tube Size
    RAll Sizes
    View Size Chart...
    Clear selection
  • C65G Metal End Cap

    POA
    This metal plug is hard to remove once it has been driven in. Note this metal insert can only be used in conjunction with tube with a wall thickness of 3.2mm. There is an alternative plastic version - C65P.
    0.050.100.120.170.29
    # Tube Size kg
    View Size Chart...
    Clear selection
  • C65P Plastic End Cap

    POA
    Plastic End Caps are available for finishing plain end tubes. Available in grey plastic they will fit medium and heavy gauge tube.
    0.0080.0100.0100.0160.024
    # Tube Size kg
    View Size Chart...
    Clear selection
  • C66 Single Mesh Clip

    POA
    The Single Mesh Clip is designed to provide a fixing for standard mesh panels. It is recommended that the clips are spaced at a maximum of 450mm apart. Available in packs of 10 only.
    # Tube Size A B C kg
    G2026.9 24 33 48 0.06
    G2533.7 27 33 52 0.07
    G3242.4 32 33 56 0.08
    G4048.3 34 33 59 0.09
    G5060.3 40 33 64 0.09
    View Size Chart...
    Clear selection
  • C67 Double Mesh Clip

    POA
    The Double Mesh Clip is designed to provide a fixing for standard mesh panels. It is recommended that the clips are spaced at a maximum of 450mm apart. Available in packs of 10 only.
    # Tube Size A B C kg
    G2026.9 24 33 48 0.09
    G2533.7 27 33 52 0.12
    G3242.4 32 33 56 0.13
    G4048.3 34 33 59 0.13
    G5060.3 40 33 64 0.14
    View Size Chart...
    Clear selection
  • C68 Weather Cowl

    POA
    The Weather Cowl is designed to cover the Railing base and provides a weather proof seal when used with a suitable flexible sealant.
    # Tube Size A B C kg
    G2533.7 143 25 125 0.28
    G3242.4 154 25 150 0.33
    G4048.3 167 25 155 0.38
    View Size Chart...
    Clear selection
  • C69 Square Plastic End Cap

    POA
    The Plastic End Caps are available for finishing plain end square tubes. Available in grey plastic they will fit medium and heavy tube gauges.
    # Tube Size A B C kg
    P40x4040x40SHS N/A 40 3.2 0.01
    P50X5050x50SHS N/A 50 3.2 0.01
    P70X7070x70SHS N/A 70 3.2 0.02
    View Size Chart...
    Clear selection
  • C70 Crimp Straight

    POA
    Straight Crimp Joints provide a permanent in-line connection for 33.7mm diameter x 3.2mm thick tube, a crimping tool is necessary.
    # Tube Size A B kg
    G2533.7 27 34 0.30
    View Size Chart...
    Clear selection
  • C71 Crimp Elbow

    POA
    Crimp Elbow provides a permanent 90° connection for 33.7mm diameter x 3.2mm thick tube, a crimping tool is necessary.
    # Tube Size A B C kg
    G2533.7 27 38 34 0.47
    View Size Chart...
    Clear selection
  • C72 Acute Angle Elbow (30° to 45°)

    POA
    Used when a junction between a sloping tube and an end post is required 30°- 45 i.e guardrail on staircases between 30° & 45°
    # Tube Size A kg
    G3242.4 57 0.98
    G4048.3 70 1.45